模具术语（英汉对照）

作者：worms 信息来源:51base.com 2006-1-7

字体大小:小 中 大网友评论条 进入论坛

一、入水：gate
  进入位：　gate location
  水口形式：gate type
  大水口：edge gate
  细水口： pin-point gate
  水口大小：gate size
  转水口：　switching runner/gate
  唧嘴口径：　sprue diameter
  二、流道: runner
  热流道：　hot runner,hot manifold
  热嘴冷流道: hot sprue/cold runner
  唧嘴直流: direct sprue gate
  圆形流道：round(full/half runner
  流道电脑分析：mold flow analysis
  流道平衡:runner balance
  热嘴：　hot sprue
  热流道板：hot manifold
  发热管：cartridge heater
  探针: thermocouples
  插头：　connector plug
  插座： connector socket
  密封/封料： seal
  三、运水：water line
  喉塞：line lpug
  喉管：tube
  塑胶管：plastic tube
  快速接头：jiffy quick connector plug/socker
  四、模具零件：　mold components
  三板模：3-plate mold
  二板模：2-plate mold
  边钉/导边：leader pin/guide pin
  边司/导套：bushing/guide bushing
  中托司：shoulder guide bushing
  中托边L：guide pin
  顶针板：ejector retainner plate
  托板：　support plate
  螺丝： screw
  管钉：dowel pin
  开模槽：ply bar scot
  内模管位：core/cavity inter-lock
  顶针：　ejector pin
  司筒：ejector sleeve
  司筒针：ejector pin
  推板：stripper plate
  缩呵：movable core,return core core puller
  扣机（尼龙拉勾）：nylon latch lock
  斜顶：lifter
  模胚（架）： mold base
  上内模：cavity insert
  下内模：core insert
  行位（滑块）： slide
  镶件：insert
  压座/斜鸡：wedge
  耐磨板/油板：wedge wear plate
  压条：plate
  撑头: support pillar
  唧嘴： sprue bushing
挡板：stop plate
  定位圈：locating ring
  锁扣：latch
  扣鸡：parting lock set
  推杆：push bar
  栓打螺丝：S.H.S.B
  顶板：eracuretun
  活动臂：lever arm
  分流锥：spure sperader
  水口司:bush
  垃圾钉：stop pin
  隔片：buffle
  弹弓柱：spring rod
  弹弓:die spring
  中托司：ejector guide bush
  中托边：ejector guide pin
  镶针：pin
  销子：dowel pin
  波子弹弓：ball catch
  喉塞: pipe plug
  锁模块：lock plate
  斜顶：angle from pin
  斜顶杆：angle ejector rod
  尼龙拉勾：parting locks
  活动臂：lever arm
  复位键、提前回杆：early return bar
  气阀：valves
  斜导边：angle pin
  术语：terms
  承压平面平衡：parting surface support balance
  模排气：parting line venting
  回针碰料位：return pin and cavity interference
  模总高超出啤机规格：mold base shut hight
  顶针碰运水：water line interferes withejector pin
  料位出上/下模：part from cavith (core) side
  模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.
  不准用镶件： Do not use (core/cavity) insert
  用铍铜做镶件： use beryllium copper insert
  初步（正式）模图设计：preliinary (final) mold design
  反呵：reverse core
  弹弓压缩量：spring compressed length
  稳定性好：good stability,stable
  强度不够：insufficient rigidity
  均匀冷却：even cooling
  扣模：sticking
  热膨胀：thero expansion
  公差：tolorance
  铜公(电极)：copper electrode

分页：